FAQ For:Bosen Garden Machine CO.，LTD

We have collected some of the most commonly asked questions submitted by our customers. If your questions are not answered here, please feel free to Contact Us.

How to use a Brush Cutter?

Step 1: Check that the brush cutter has a sufficient amount of string. Locate the rotary device, found at the end of the brush cutter opposite the handle and motor. The oval rotary device will have two or more holes on its side, out of which protrudes the plastic string. Remove the cover and look inside to check that there are several wraps of string around the device.
Step 2: Replace the cover and check that the rotary device spins freely. If the brush cutter has been used before, check that there are no leaves, vines or debris stuck on the end that prevent the rotary device from moving.
Step 3: Check that the brush cutter has gasoline in its engine. The engine is found at the end of the tool opposite the rotary device. Remove the gas cap and look inside. If the gasoline levels appear low, top off the reservoir with gasoline using a funnel to prevent dripping. Close the gas cap.

Step 4: Start the brush cutter. Brush cutters can typically be started in one of two ways, depending on the make and model of the tool. Some are started by holding down the start button and pulling a rope in the engine akin to that found in a lawn mower or boat engine. Newer brush cutters may be started by pulling a trigger on the engine.

Step 5: Give the brush cutter 30-60 seconds to warm up. During this time, rev the engine a couple of times by pressing the trigger in the tool's handle. This injects more fuel into the engine and causes the device to spin faster.

Step 6: Apply the brush cutter to the plants and vegetation that you want to remove or trim. Hold the brush cutter's head several inches away from the plant and rev the engine. The plastic string in the rotary device will cut back the plant. Move the tool back and forth in slow, sweeping motions if you are cutting down swaths of plants, such as grass in a field.

Tips & Warnings

• The denser and heavier the vegetation that you are cutting, the more string the brush cutter will use.M
• Wear protective gear such as eyeglasses and jeans to protect yourself from flying debris when using a brush cutter.

How to Trim a Tree With a Chainsaw?

• Step 1: Examine your property for tree limbs that require trimming. Tree limbs that join the trunk above your shoulder height are too high to safely trim with a chain saw. Clear any debris from the area to insure safe footing.
• Step 2: Dress appropriately. Put on a long-sleeved shirt and long pants, heavy duty work boots, helmet, ear plugs, goggles or safety glasses and work gloves.
• Step 3: Start the chain saw. Make an undercut on the first limb you need to trim. Start about six inches from the tree trunk, position your chainsaw directly beneath the limb, and cut one-third of the way through the limb.
• Step 4: Reposition the chainsaw blade to a corresponding location directly above the undercut on the limb and cut down the rest of the way through through the limb. This process is called "overcutting." Allow the limb to fall to the ground. Position the chainsaw blade above the remaining stub to within two inches of the trunk. Overcut the stub all the way through.
• Step 5: Turn the chain saw to its off position and wait for the engine to quit running. Put the chain saw down. Clear the fallen limb from the work area. Repeat steps three and four for any additional limbs that need to be trimmed.
• Step 6: Remove trimmings. If you have a chipper, you can chip the trimmings into mulch. Otherwise, check with your local solid waste department for disposal options.

How to Start a Gas Chainsaw?

A chainsaw can be a very handy tool to have around, from cutting firewood to trimming trees or fallen limbs from a storm or even creating your own lumber. The list of uses for a chainsaw is a long one. But just starting a chainsaw can be a frustrating task if you don't follow a very specific process. This article will help you understand that process, eliminate frustration and even drastically reduce blood pressure and cursing! It may even save the life of a chainsaw you love. So don't throw that saw into the creek just yet. Follow these simple instructions and get it cranked up!

How to Mix Gas and Oil for Chainsaw Fuel?

Fueling a chainsaw is not quite as straightforward as putting gas in your car. Two-stroke engines, like the one in your chainsaw, require a mixture of gasoline and oil. If you don't properly mix oil into your fuel, you will quickly ruin your chainsaw's motor

• Fueling a chainsaw is not quite as straightforward as putting gas in your car. Two-stroke engines, like the one in your chainsaw, require a mixture of gasoline and oil. If you don't properly mix oil into your fuel, you will quickly ruin your chainsaw's motor
• Step 2: Use only two-cycle oil for your mixture. This oil is made especially for these engines and can be purchased at gas stations, hardware stores or any other place where you buy regular motor oil.
• Step 3: Pour the proper amounts of gas and oil into a fuel can. Shake the can well to mix it.
• Step 4: Label your gas can with the mixture ratio. You can use the same mixture for other two-stroke engines.

How to Troubleshoot Gas Chainsaws?

IThere are two basic parts of a chainsaw, the motor and the bar that carries the chain. Both of these parts can contribute to a chainsaw malfunction and in most cases can be repaired without the help of a professional. Even if you have not worked with a gas chainsaw much in the past, you can still take some steps to fix yours on your own before bringing in a chainsaw technician or simply replacing the tool.

. Take your spark plug wrench, which is just a wrench head with a handle that literally snaps in place on the spark plug, and remove the spark plug by turning it counterclockwise. Spray a blast of starting fluid inside the spark plug hole, maybe a half a second's worth, and then put the plug back in. Tighten it down.

How to Compare Gasoline Hedge Trimmers?

Any home owner whose yard contains hedges or overgrown bushes knows about the time-consuming process of manual hedge or bush trimming. Gas-powered hedge trimmers power through the task of hedge trimming. In just a few swipes, you can even out the tops, sides and bottoms. You can sculpt a hedge or bush to just about any shape you want, quickly and efficiently. If you have hedges, your new best friend consists of a gas-powered hedge trimmer.

How to Choose Hedge Trimmers?

Hedges can serve a dual purpose, they can add a decorative touch to your lawn or serve as a way to screen the yard from people going by. To keep your hedges looking their best, you need to choose the right hedge trimmer. Factors to consider in choosing a trimmer include the size and amount of hedges to trim, cost of the trimmer and benefits and drawbacks of the different models. After weighing all the options, you will end up with the right trimmer for the job.

How Does a Hedge Trimmer Work?

Trimming the hedges is just part of the landscaping chores many people must do during the growing season. Hedge trimmers come in a variety of sizes and types to make that job a little bit easier. The type of trimmer used depends on the job it is used for. There are large yards where the hedges are far away from an electrical source and then there are the hedges close to the house that just need some new growth cut off in the spring and fall. Whatever the job may be, there is a trimmer out there for it. In some cases, you may even need two separate trimmers, one for detailed work and one for heavy duty work.

Types and Sizes of Hedge Trimmers

Hedge trimmers come in electric corded, gas and rechargeable electric types. Most of the time they are used according to preference, but sometimes the job demands a certain type of trimmer. Corded electric trimmers are the most common and economical but if your hedges are over 100 feet away they aren't the most feasible. They are also the lightest weight, which makes them easier to carry around while getting the job done. Gas powered trimmers are the best for hedges over 100 feet away from a power source, but are heavier than the corded ones. This makes it harder on the user if there are a lot of hedges to trim. Battery operated trimmers are also heavy and can only be used for a half hour to three hours at a time depending on the style of trimmer. They are convenient in the fact that you can go anywhere with them though and you can always take along extra batteries.

How to Buy a Hedge Trimmer?

Keeping your hedge trimmed properly can help make your yard and garden more appealing. But trimming can be time-consuming and difficult. Buy the right kind of hedge trimmer and it can make your work easier, faster and neater. Read on to learn how to buy a hedge trimmer.

How to Use a Pressure Washer?

Pressure washing can be a quick, easy way to clean your car, driveway, deck or siding. However, the powerful stream of water can also inflict damage if not handled properly. By learning a few techniques and principles, you'll get the job done more quickly and won't risk harming your home or family in the process.

What’s an earth auger?

Concrete vibrator designs range in size from small battery-powered wands to much larger plug-in versions that be used on very deep pours. In all cases, a concrete vibrator that can reach the bottom of the pouring forms should be used, ensuring even treatment of the entire concrete pour. Attachments for the concrete vibrator are selected on the basis of the depth of the pour and the type of concrete being used.